Welding Repairs for Cheam Cars, from Our Hackbridge Workshop

Cheam has plenty of older, carefully kept cars that are mechanically sound but starting to rust underneath. Our Hackbridge workshop is about 12 minutes from Cheam, and we repair corrosion by cutting it out and welding in new steel, protected so it lasts.

  • ★★★★★ 4.9/5 from 193 Google reviews
  • ~12 min from Cheam
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

Older, well-kept Cheam cars and the rust you can't see

Drive round the inter-war roads of North Cheam or the streets near the Cheam Village Conservation Area and you see a lot of cars that have been looked after for years. Low mileage, full service history, tidy paintwork. Underneath, though, age catches up with any steel body, and the sills, rear arches and floor seams are where it shows first. The owner is often surprised when a first corrosion advisory appears on the MOT, because the car looks so good from the kerb.

Low-mileage cars have a particular weakness. They're used for short trips to Cheam station or the shops and then sit, so water and winter salt picked up on the A217 stay underneath instead of being dried off by a longer run. Garaged cars aren't immune either, if they go in wet. Rust in those conditions works slowly from inside the sills and around the jacking points. Condensation in a closed garage can add to the problem, especially in a cold snap after a wet run.

For these cars we take a careful approach. We inspect the whole underside, separate structural corrosion from cosmetic, and fabricate repair sections to match the original shape where pre-formed panels don't fit well. On classic and older cars we keep the repair as neat and sympathetic as possible, seam sealing the joints and treating the sills with cavity wax. The work is quoted in writing before we start, and we'll call if the metal is worse than expected. Where an earlier repair has been done badly, with a plate welded over rotten metal or filler across a sill, we cut it out and do it again properly, because that sort of repair traps water and can be failed by a tester.

Buying an older car in Cheam is also a good time to see us. A pre-purchase underside inspection can show whether the car needs welding soon, which is useful when you're negotiating. Repairs we carry out come with our 12-month workmanship warranty. We'll also tell you if a car you're considering has too much rust to be worth the money.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

From £80Written quote first
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty
4.9★193 Google reviews

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

From Cheam to our Hackbridge workshop

From Cheam Village crossroads head east on the A232 (Cheam Road) into Sutton, follow it through the town centre one-way system and on to Carshalton past the ponds. In Carshalton take the B277 north via Hackbridge Road into Hackbridge, then join London Road (A237); Soho Mills is by Hackbridge station. Alternatively stay on the A232 (Acre Lane) to Wallington Green and turn north up London Road (A237).

From Cheam Village crossroads take the A232 through Sutton to Carshalton, then Hackbridge Road to London Road in Hackbridge, about 12 minutes. For a larger job we can collect the car from Cheam and return it once the welding is done.

Directions from Cheam

About Cheam

Cheam is a leafy, mostly residential suburb on the western side of the London Borough of Sutton, split into Cheam Village, North Cheam and South Cheam. The village grew up around a crossroads and keeps a conservation-area feel, with Tudor and Georgian buildings alongside 1920s–30s mock-Tudor shopping parades, while the surrounding streets are largely inter-war semis and detached family houses. North Cheam, a mile to the north around the A24, is busier and more commercial. Driving is mostly on wide suburban roads, but the village crossroads and the main A-roads through it get congested at peak times.

Places nearby: Nonsuch Park, Nonsuch Mansion, Cheam Park, Whitehall, Lumley Chapel, St Dunstan's Church

Postcodes: SM3, SM2 · London Borough of Sutton

More about KITH for Cheam drivers

Welding & Rust Repair in Cheam: your questions answered

Do you weld classic cars, not just MOT repairs?

Yes. We can fabricate repair sections to match the original shape and keep the work tidy and sympathetic. We'll talk through what's structural and what can be left, so you can plan the work over time if you prefer.

Can you check the underside of a car before I buy it?

Yes, a pre-purchase underside inspection is a sensible step for any older car. We put it on the ramp, probe the sills, floors and mountings, and tell you what welding it's likely to need. That helps you decide whether the asking price is fair.

My garaged car has a corrosion advisory. How did that happen?

A car that goes into the garage wet, or does mostly short trips, can stay damp underneath for long periods. Rust then starts inside sills and seams. It's worth getting it looked at before the next winter so the repair stays small.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Price your welding and rust repair now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection from Cheam can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Loading instant quote…
Chat on WhatsApp