Electrical · Cheam SM3

ABS Sensor Replacement near Cheam and North Cheam

From Cheam it's about 12 minutes to our workshop in Hackbridge along the A232. If the ABS, traction or stability light has come on, we find which wheel is at fault and why, and ABS sensor replacement starts from £89.

Get an instant price Call 020 4629 9469

★★★★★ 4.9/5 from 87 Google reviews
~12 min from Cheam
Mon–Sat 8am–8pm

Audi SQ5 in for brake and wheel-speed work at KITH Cars Garage & Bodyworks, Hackbridge

ABS Sensor Replacement for Cheam drivers

North Cheam's busy crossroads and wheel speed signals

The North Cheam crossroads, where Malden Road meets the A24 London Road, is busy with supermarket and drive-through traffic, and The Broadway and Malden Road carry steady buses and local cars between the village and North Cheam. That's plenty of stop-start driving where a sudden brake is sometimes needed, and where ABS and stability control earn their keep. When a sensor drops out, both switch off and the warning lights come on, so you lose that safety net until it's fixed, and the car will fail its MOT if the light is still on.

Many cars in Cheam are newer models where the wheel speed sensors do more than run the ABS. On a lot of them the same signals feed hill-hold, the electronic parking brake's automatic functions, cruise control and the tyre pressure warning. A driver in East Cheam might first notice that auto-hold no longer works, or a tyre warning won't clear, before connecting it to the ABS light. Weekend trips out to Nonsuch Park and Nonsuch Mansion, with a run over the car park and park roads, are also when intermittent wiring faults often reveal themselves.

We diagnose these cars carefully. We read the fault codes from the ABS module and any related systems, compare live wheel speeds on a road test and test the sensor circuit. If the fault is in a magnetic encoder built into the wheel bearing, we'll explain why a sensor alone won't cure it. Some cars need a steering angle or other calibration after the repair, and we'll do that where required. Everything is set out in a written quote.

The drive is east on the A232 through Sutton and Carshalton, then north on the B277 to Hackbridge, about 4 miles. With just the ABS light on, most cars can be driven here carefully, and many jobs are finished the same day. Our 3-month workmanship warranty covers the repair.

Electrical

ABS Sensor Replacement: what’s involved

Each wheel has a speed sensor that reads a toothed or magnetic ring turning with the hub or driveshaft. The ABS module constantly compares the four signals. If one wheel slows too quickly under braking, the system releases and reapplies that brake to stop it locking. The same signals feed traction control, stability control and often the speedometer, hill-hold and tyre pressure warning.

Older cars use passive sensors that generate their own signal. Most modern cars use active sensors, which are powered by the ABS module and often read a magnetic encoder built into the wheel bearing seal. Sensors sit right next to the brakes, exposed to heat, water, salt and brake dust, so corrosion, damaged wiring and failed connectors are common. When a signal drops out, the system switches ABS and stability control off and lights the warning. Your normal brakes still work.

From £89Written quote first

45 minutes–2 hoursTypical time in the workshop

3 monthsWorkmanship warranty

4.9★87 Google reviews

Signs of an ABS sensor fault

ABS warning light on

A steady ABS light means the system has switched itself off. Normal braking still works, but the wheels can lock under heavy braking.

Traction and stability lights too

Because they rely on the same wheel speed signals, the traction control or ESP light usually comes on with the ABS light.

Light comes and goes

An intermittent warning, often after bumps, in wet weather or at a certain speed, usually points to damaged wiring, a loose connector or a corroded sensor.

ABS pulsing at low speed

If the pedal pulses and the ABS activates when stopping gently, a sensor may be giving a false reading from a dirty sensor or a cracked reluctor ring.

Speedometer or tyre warning faults

On cars that take road speed or tyre pressure monitoring from the wheel sensors, a faulty sensor can upset the speedometer or set a tyre warning.

Other systems disabled

Hill-hold, cruise control, stop-start and some electric parking brake functions may stop working when a wheel speed signal is missing.

When should it be done?

ABS sensors have no replacement interval. They are replaced when they fail or when their wiring is damaged. Get the car checked as soon as the ABS light comes on, because the car won't stop as well in an emergency on a wet road without ABS and stability control. An ABS warning light that stays on is also an MOT failure. Faults often show up after brake, hub or suspension work, when a sensor or its wiring may have been disturbed.

ABS, traction or stability warning light on
Intermittent warnings in wet weather or over bumps
Warning lights after brake, wheel bearing or suspension work
Before an MOT if the ABS light is showing

How we replace an ABS sensor

Check-in and symptomsWe ask when the light appears and whether any work has been done recently, as disturbed wiring after brake or suspension work is common.
Diagnostic scanWe read the ABS module fault codes to identify which wheel is affected and whether the fault is signal, circuit or plausibility related.
Live data and testingWe compare live wheel speed readings on a road test or ramp and test the sensor circuit with a multimeter or oscilloscope to separate sensor, wiring and ring faults.
Inspect the ring and bearingWe check the reluctor ring or magnetic encoder for cracks, corrosion or damage and check the wheel bearing for play, as either can cause a false signal.
Written quoteWe explain the cause and give you a written quote. If the encoder is built into the wheel bearing, we'll explain why the bearing may need replacing.
Replace the sensorWe carefully remove the old sensor, which is often seized in the hub, clean the mounting, and fit the new sensor with its wiring routed and secured correctly.
Clear codes and road testWe clear the fault codes, road test to confirm all four wheel speeds read correctly and the warning lights stay off, and run any calibration the car needs.

Parts we fit

Sensors must match the car exactly. Active and passive types are not interchangeable, and connectors and lengths vary between models and even between axles. We fit OE or OE-equivalent sensors from manufacturers such as Bosch, ATE or Continental. Where the wiring is damaged we repair it properly with sealed connectors, and where the fault is in a reluctor ring or a wheel bearing encoder, we replace that part rather than just the sensor.

OE or OE-equivalent ABS wheel speed sensors
Reluctor rings where cracked or corroded
Wheel bearings with integral magnetic encoders where required
Sensor wiring and sealed connector repairs

How long it takes

45 minutes–2 hours

A straightforward sensor swap often takes under an hour. Seized sensors, wiring repairs or a reluctor ring or wheel bearing replacement take longer. Most jobs are completed the same day.

What’s included

ABS system fault code scan
Wheel speed live data check
Sensor circuit and reluctor ring inspection
Correct replacement sensor fitted
Fault codes cleared
Road test to confirm the warning lights stay off

Getting here from Cheam

From Cheam to our Hackbridge workshop

From Cheam Village crossroads head east on the A232 (Cheam Road) into Sutton, follow it through the town centre one-way system and on to Carshalton past the ponds. In Carshalton take the B277 north via Hackbridge Road into Hackbridge, then join London Road (A237); Soho Mills is by Hackbridge station. Alternatively stay on the A232 (Acre Lane) to Wallington Green and turn north up London Road (A237).

Take the A232 east through Sutton and Carshalton, then the B277 north to Hackbridge, about 12 minutes. With only the ABS light on, drive gently and leave extra room.

Directions from Cheam

About Cheam

Cheam is a leafy, mostly residential suburb on the western side of the London Borough of Sutton, split into Cheam Village, North Cheam and South Cheam. The village grew up around a crossroads and keeps a conservation-area feel, with Tudor and Georgian buildings alongside 1920s–30s mock-Tudor shopping parades, while the surrounding streets are largely inter-war semis and detached family houses. North Cheam, a mile to the north around the A24, is busier and more commercial. Driving is mostly on wide suburban roads, but the village crossroads and the main A-roads through it get congested at peak times.

Places nearby: Nonsuch Park, Nonsuch Mansion, Cheam Park, Whitehall, Lumley Chapel, St Dunstan's Church

Postcodes: SM3, SM2 · London Borough of Sutton

More about KITH for Cheam drivers

Questions

ABS Sensor Replacement in Cheam: your questions answered

Why has my tyre pressure warning come on with the ABS light?

Many cars measure tyre pressure indirectly by comparing wheel speeds. When one sensor fails, the system can't do that and sets its own warning. Once the sensor is fixed, the tyre system usually needs resetting, which we do.

Will the ABS light stop my car passing its MOT?

Yes. An ABS warning light that stays on is an MOT failure. If your MOT is due soon, book the repair before the test so the car isn't failed for it.

Does my car need calibrating after a new ABS sensor?

Most don't, but some need a steering angle reset or a system initialisation after brake and ABS work. We check what your model requires and complete it before the road test.

Is it safe to drive with the ABS light on?

The car will still brake normally, so you can usually drive it carefully to the garage. But without ABS and stability control the wheels can lock under hard braking, so leave extra distance. If the brake warning light is on as well, get advice before driving.

Will an ABS light fail the MOT?

Yes. An ABS warning light that stays on, or doesn't come on when the ignition is switched on, is an MOT failure. The same applies to the electronic stability control warning on cars that have it.

Can I just clear the code?

If the fault is still there, the ABS module will find it again, usually within a short drive. Clearing codes without finding the cause just delays the repair.

Why might I need a wheel bearing as well?

On many modern cars the magnetic ring that the sensor reads is built into the wheel bearing seal. If that encoder is damaged or the bearing has excessive play, a new sensor won't cure the fault, and the bearing has to be replaced.

Why did the light come on after my brakes were done?

ABS sensors and their wiring sit close to the brakes and hubs, so they can be knocked, stretched or left unplugged during brake or suspension work. Sometimes an old sensor that was already corroded fails when disturbed. A quick scan shows which wheel is affected.

Instant quote

Price your ABS sensor replacement now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

Free, about 30 seconds, no sign-up
Parts, labour and VAT included
3-month workmanship warranty
Collection from Cheam can be arranged

“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Loading instant quote…

More for Cheam drivers

Brake Repairs in Cheam · Wheel Bearing Replacement in Cheam · Engine Diagnostics in Cheam · MOT Testing in Cheam · Car Servicing in Cheam · Clutch Replacement in Cheam · Accident Repairs in Cheam · Tyre Fitting in Cheam · Vehicle Recovery in Cheam

ABS Sensor Replacement across South London

ABS Sensor Replacement Sutton · ABS Sensor Replacement Worcester Park · ABS Sensor Replacement Carshalton · ABS Sensor Replacement Morden
Beddington · Coulsdon · Croydon · Mitcham · Norbury · Purley · Rosehill · Streatham · Thornton Heath · Tooting · Wallington · Wimbledon